Features

?Package in 8mm tape on 7〞diameter reel.

?Compatible with automatic placement equipment.

?Compatible with infrared and vapor phase reflow solder process.

?Mono-color type. ?Pb-free.

?The product itself will remain within ROHS complaint Version. 

Descriptions

?The 17-21 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained.

?Besides, lightweight makes them ideal for miniature applications. etc. 

Applications

?Automotive: backlighting in dashboard and switch.

?Telecommunication: indicator and backlighting in telephone and fax.

?Flat backlight for LCD, switch and symbol.

?General use.

17-21/ BHC - AN1P2/3T，blue-ray 0805 SMD LED alternative specifications17-21/BHC-AP1Q2/3T, due to the continuous development of blue chip photosynthetic efficiency, the original specification N1 and P2 has not adapt to the brightness range, EVERLIGHT in 2017 has been eliminated the low luminance specifications 17-21 / BHC AN1P2/3T, the follow-up has 0805 blue-ray specification for 17 - 21 / BHC - AP1Q2/3T, 0805 blue patch LED: 17-21 / BHC - AP1Q2/3T rated maximum conditions of use range (temperature 25 ℃) : 0805 blue patch LED: 17-21 / BHC - AP1Q2/3 t rated maximum conditions of use range (temperature 25 ℃) :

The project identifies the maximum range unit of the symbol

Reverse voltage VR 5 V

The forward current IF 25 mA

Peak current (pulse 1/10,1 kilohertz) IFP 100 mA

Power consumption Pd 95 W

Antistatic ability (electrostatic mode) ESD 150 V

Working temperature Topr - 40 ~ + 85 ℃

Storage temperature Tstg - 40 ~ + 90 ℃

Soldering temperature Tsol infrared baking furnace: 260 ℃ / 10 seconds, hand soldering: 350 ℃ / 3 seconds

Precautions For Use

1. Over-current-proof

Customer must apply resistors for protection, otherwise slight voltage shift will cause big 

current change ( Burn out will happen ).

2. Storage

2.1  Do not open moisture proof bag before the products are ready to use.  2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 

2.3 After opening the package : The LEDs should be kept at 30℃ or less and 70%RH or less(Floor life).

    However, it's recommended that the LEDs should be used within 168 hours (7 days) after opening 

the package. If unused LEDs remain, it should be stored in moisture proof packages. 

2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the 

storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours.

3. Soldering Condition

3.1 Pb-free solder temperature profile

3.2 Reflow soldering should not be done more than two times.

3.3 When soldering, do not put stress on the LEDs during heating.

 3.4 After soldering, do not warp the circuit board.

4.Soldering Iron        

Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.

5.Repairing      

Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing